+8618858210064-
Guide to Insulation: Spray Foam
Made from polyurethane, this product reduces air leakage better than any other type of insulation. It fills the nooks and crannies of unusually shaped building cavities easily. There are two main types of spray foam: open-cell spray foam, which has a density of about 1⁄2 lb. per cu. ft.; and clos...
-
What is the differences in Oil-Based and Latex Paints?
Painting is the nation's number-one home-improvement project. It can help you change the look of a room from dull to brand new. Here's an interior-painting primer, starting with the pros and cons of oil-based and water-based, or latex, paints. Oil-based paint is more durable, but it takes long...
-
WHAT KIND OF PAINT MATERIAL I CAN USE FOR MY DP-X3 DP-X6 AIRLESS PAINT SPRAYER?
DP-X3 is with motor power 550W, max. Flow rate 1.0L/min and max. Tip size 0017”. DP-X6 with motor power 650W, max. Flow rate 1.4L/min and max. Tip size 0019”. DP-X3 or DP-X6 is applicable for spraying low viscosity paint material like latex and acrylic coatings, enamel, lacquer, stains, emulsi...
-
Tips for Operating X-3 and X-6(H) Airless Paint Sprayers
Tips/Guidance for Operating X-3 and X-6(H) Airless Paint Sprayers are as below for users' reference. X-3 / X-6(H) airless paint sprayers are with OILESS DESIGN(PATENTED), no need to additionally add lubricating oil into the piston pump. Pls clean the pump / hose / spray gun / spray tip throu...
-
HOW TO ASSEMBLE MY X3 X6 DIY AIRLESS SPRAYER
tools: cross point screwdriver, sharp vise, vise, allen wrench, Mobil EP0 grease, Mobil XHP 222 grease etc. sleeve coated with Mobil EP0 grease, that's very important. install v-packing on airless sprayer piston rod install v-packing and sleeve in by using vise, and please make sure that ...
-
HOW TO DISASSEMBLE MY X3 AIRLESS SPRAYER
tools: cross point screwdriver, sharp vise, allen wrench, alcohol, cotton swabs etc. unscrew the nuts in front of cover by cross point screwdriver unscrew the nuts of motor cover by cross point screwdriver unplug airless puressure regulator connector unplug other lines and remove the c...
-
how to chose the airless paint spray tip size for your paint material
how to chose the airless paint spray tip size for your paint material? The following tables display several paint applications with suggested corresponding paint spray tips. These spray tip sizes are merely recommendations and popular in the market. You can buy the spray tip from any of airless pa...
-
Viscosity Tables,Viscosity chart
Viscosity is the measurement of a fluid's internal resistance to flow. This is typically designated in units of centipoise or poise but can be expressed in other acceptable measurements as well. Some conversion factors are as follows: 100 Centipoise = 1 Poise 1 Centipoise = 1 mPa s (Millipascal ...
-
resource about painting sprayer and coating related
Accelerator: A substance that when added to a paint will speed up the rate of cure. Acetone: A very fast evaporating solvent with high solvency for certain types of compounds and resins. Has a characteristic ether-like odor. Acrylic Urethane: A coating based on urethane chemistry, which ...
-
why the paint runs or sags down the wall when I spray
Why the paint runs or sags down the wall when I spray? Answer: The paint is going on too thick. This can be caused by a number of things. The operator is not moving the airless spray gun fast enough. Increase the speed that the gun is being moved over the painting surface. Select a spray tip with a...
-
Why do I get streaks or bands in my spray pattern
Why do I get streaks or bands in my spray pattern? Answer: Streaks in the spray pattern, especially heavy bands at the outside edge, indicates low pressure at the tip. In order to correct the issue, turn up the pressure control knob until these bands are eliminated. If the sprayer is already at maxi...
-
How to chose proper pneumatic airless pump for the painting application?
For the pneumatic pump, there are many different pressure ratio for one model, and the table below can help you for easy understanding the difference between them and choice the suitable products for your application. Air-driven airless spray unit Model Pressure ratio （L/min）Max output App...
-
What cleaner should I use to clean my airless sprayer after spraying?
To make it simple, you should use whatever the thinner is for the material you are spraying. E.g. Latex = Water Oil-base = Mineral Spirits Lacquer = Lacquer thinner After thoroughly cleaning your sprayer you need use a protectant such as pump armor. Dino-power is pr...
-
Which airless sprayer can spray waterproofing polyurethane paint?
Generally, the waterproofing polyurethane paint will be applied for the basement,grain depot ,exterior wall and roof etc. The most common application will be the Liquid Roofing, which is the process of waterproofing a roof by the application of a specialist liquid roof coating. It is suited to all ...