MENU
4.3/5 - (9 votes)

Airless Disinfectant Sprayer For Sanitzing And Disinfecting

Airless disinfectant sprayer

Why you should spray disinfectant?

Since first being recorded, the Covid-19 has spread around the world in most countries, and it had been declared a pandemic by the World Health Organization.

In addition to direct human-to-human transmission, contaminated surfaces also pose a risk of transmitting viruses and pathogens.

Especially in the current COVID-19 pandemic, this is of great importance: Studies show that Covid-19 viruses can survive for several days on surfaces that we come into daily contact with.

Where can spray disinfection be used?

Particular attention must be paid to areas in daily use, as well as to areas frequented by people who are or were already ill.

Office Spaces/Conference room

Restaurants and food preparation areas

Public transport(bus, subway, train, station etc)

Schools

Healthcare Center

Fitness places

disinfection application

With which products is disinfection possible?

1.SMALL SURFACES

electric spray gun

Model No. DP-003 DP-007 DP-006 DP-008
Voltage 220V~50Hz /  120V~60HZ 220V~50Hz /  120V~60HZ 220V~50Hz /  120V~60HZ 220V~50Hz /  120V~60HZ
Rated Power 600W 350w 600W 700W
Water Flow Rate 800ml/min 180ml/min 1000ml/min 1400ml/min
Max. Viscosity 60 DIN-s 50 DIN-s 60 DIN-s 60 DIN-s
Nozzle Size Φ2.0mm Φ2.5mm Φ2.5mm Φ1.8mm  /  Φ2.5mm
Paint Cup Capacity 800ml 800ml 800ml 800ml
Air Hose Length 1.5 meters NA 1.8 meters 3.0 meters
Cordset 1.8meters 1.8meters 2meters 2meters

2.MEDIUM SIZE SURFACES

X6 AIRLESS DISINFECTANT SPRAYER


Item No. X6(Standard) X6V(Hopper type) X6H(Cart type)
Power supply 220v/50hz or 110v/60hz 220v/50hz or 110v/60hz 220v/50hz or 110v/60hz
Motor power 650W Universal Motor 650W Universal Motor 650W Universal Motor
Max.Flow rate 1.4L/MIN 1.4L/MIN 1.4L/MIN
Max. tip size 0.019″ 0.019″ 0.019″
Max.Working pressure 200bar/2900psi 200bar/2900psi 200bar/2900psi
Net/Gross weight 5.7/8.7kgs 6.5/8.8kgs 11.5/15.5kgs
Contents X-450 Gun, X 517 Spray Tip,
X Guard,1/4 in x 7.5M Airless
Hose, 30cm extension pole,
Wrench kit, brush, and
manual.
5L Hooper with lid, X-450 Gun,
X 517 Spray Tip,X Guard,
1/4 in x 7.5M Airless Hose,
30cm extension pole,
Wrench kit, brush, and manual.
X-450 Gun, X 517 Spray Tip,
X Guard, 1/4 in x 7.5M
Airless Hose,
30cm extension pole,
Wrench kit, brush,
and manual.

3.LARGE SURFACES

AIRLESS DISINFECTANT SPRAYER

Item No. SP450 X20 X980(Diaphragm pump)
Power supply 220v/50hz or 110v/60hz 220v/50hz or 110v/60hz 220v/50hz
Motor power 1000W PMDC Motor 1100W PMDC 1500W Induction motor
Max.Flow rate 1.8L/MIN 2.0L/MIN 3.6L/MIN
Max. tip size 0.021″ 0.021″ 0.023″
Max.Working pressure 200bar/2900psi 200bar/2900psi 220bar/3190psi
Net/Gross weight 13.5/19.5kgs 14.9/20.1kgs 38.0/45.5kgs
Contents in package DP-6371 airless spray gun with 517,
1/4” 13M high pressure hose,
45cm extension pole, lubricating oil.
And manual.
X-450 Gun, X 521 Spray Tip, X Guard,
1/4 in x 15M Airless Hose,
45cm extension pole,  lubricating oil.
wrench set,pressure gage and manual
X-450 Gun, X  Spray Tip, X Guard,
1/4 in x 15M Airless Hose,
45cm extension pole, pressure gage,
wrench set, lubricating oil and manual

What can be disinfected?

Spraying technology allows a comprehensive surface coating with disinfectant

subsequently the microbial presence of bacteria, fungi or viruses can be reduced.

Disinfectants in liquid form, which are at least limited virucidal, are suitable for application to surfaces by spraying.

Disinfectant types: Based on alcohol, aldehydes, biguanides, bisphenols, diamidines, peroxygens, phenolics, quaternary ammonium salts and halogen-releasing compounds.

Whom is suitable for spraying disinfection?

The Spraying of Disinfection solutions is commonly undertaking by the following groups:

Cleaning & Sanitation Providers

Health and Care Providers

Municipality Workers

Janitors, Commercial and Residential Facility Managers

Safety authorities: Military and Reservists

How does spray disinfection of surfaces work?

Setup

Tighten the connections on the device firmly and check the seal of the device with water before using it with disinfectant.

Evacuate the water.

Fill disinfectant into the hopper or place suction system directly in the material container.

Pressure setting: 70-100 bar

Nozzle selection: (recommendation 515,617,619)

When using other nozzles, the application speed must be adjusted

Apply disinfectant quickly and evenly to the surfaces according to the material recommendations.

Please refer to the manufacturer’s instructions for exposure times of the disinfectant you are using.

Safety Instructions

Please observe the following safety instructions before use:

Always wear the necessary personal protective equipment (PPE, see safety data sheet of the device: gloves, goggles and mask).

Never point the fluid stream at people or animals – there is a risk of injury.

Thoroughly read the operating instructions of the machine as well as the safety data sheet of the material and follow the instructions contained therein.

Do not spray any electrical devices and equipment.

Check the filters in the gun and sprayer daily after each use and clean or replace as necessary.

When using flammable liquids, the machine must be operated outside the room where the spraying occurs (danger zone = 5 m distance from the application area).

If flammable disinfectants are used, sufficient ventilation must be ensured. Furthermore, no warm or hot surfaces are to be disinfected. If possible, electrical systems should be switched off and light switch operations prevented. There is a risk of explosion!


         

Video

  • Related products
  • Related posts
  • Comments
  • FAQ

Leave your comments

Name *

Mail (will not be published) *

Country *

FAQ regarding our business

Q1: What's your MOQ minimum order quantity for formal order?

A: Our MOQ is 10-100 units depends on the model. For small pump or spray guns , the MOQ is 100. and for large capacity pump, the MOQ could be 10. We can accept 1 or 2 units for sample testing order.

Q2: What's your payment terms?

A: We could accept L/C, T/T and Paypal or Western Union, also accept the payment against B/L copy . We can offer credit payment term for our long year cooperated representatives.

Q3: What is the lead time?

A: Sample order: 3-5days, mass production 20-40 days for the formal order.

Q4: Can we put our logo on your products? Is there extra charge for it?

A: Yes, we accept the OEM order based on the order quantity. The color box package need extra cost for less container order.

Q5: What's your warranty?

A: our warranty is 12months limited warranty except the easily worn parts. and for the motor we offer 2 years warranty.

Q6. Which port do you ship your machines?

A: We ship from Ningbo port China. for the FOB price, we will bear the local freight charge and the forwarder fee / customs fee, and all the shipping cost / insurance cost / forwarder cost at destination port / import duty tax ... all will be beared by the buyer (or importer).

Q7. how can i buy your products?

A: if you're final user, please leave your mobile phone number to us, and we will ask our distributor / dealer to call you directly. if you want to be our distributor or representative, welcome to contact us by email or whatsapp. we can talk more details one by one, we're sure you would be satisfied with our quality / service and price.

Inquiry

    * Your Name *

    Your Phone

    * Your Email Address *

    Your Country

    * Message *